<pre id="z9x5z"></pre>

              當前位置:首頁-新聞中心 > 新聞中心

              螺旋風管其長度等方面是要好于矩形風管

              發布人:http://www.globalcarsourcing.com   發布時間:2022-11-17 19:52:03

              螺旋風管其長度等方面是要好于矩形風管:這是由于普通的螺旋風管,其正常長度是為3米到6米,而矩形風管其是為1米到1.5米,除此之外,螺旋風管的長度,還能夠依照具體需求來定做,從其它方面來看,螺旋風管中的連接點,是能夠很大程度上根絕的,由于其風管之間的連接,只用管接件,而矩形風管則需求雙法蘭體系。

              The length of spiral air duct is better than that of rectangular air duct: this is because the normal length of ordinary spiral air duct is 3 to 6 meters, while that of rectangular air duct is 1 to 1.5 meters. In addition, the length of spiral air duct can also be customized according to specific needs. From other aspects, the connection points in spiral air duct can be eliminated to a large extent. Because the connection between air ducts only uses pipe connectors, The rectangular air duct requires double flange system.

              1、通風管道加工的過程中應該盡量避免出現縱向接縫,但是一定不能出現橫向接縫。而且通風管道的咬口縫和四角的縫隙處,需要按照設計潔凈等級要求,然后還要采用密封膠將其堵嚴。另外通風管道板材的連接縫的密封面應該設在通風管道壁的正壓側。

              1. The longitudinal joint shall be avoided as far as possible during the processing of the ventilation pipe, but the transverse joint shall not be allowed. Moreover, the seaming seams and the four corners of the ventilation pipe shall be sealed with sealant according to the design cleanliness level requirements. In addition, the sealing surface of the joint of the ventilation duct plate should be set at the positive pressure side of the ventilation duct wall.

              鍍鋅螺旋風管

              Galvanized spiral air duct

              2、加工的時候,不能在通風管道內部設置加固框或者加固筋,因為這樣對于通風管道的質量會造成一定的影響。

              2. During processing, reinforcing frames or reinforcements cannot be set inside the ventilation ducts, because this will have a certain impact on the quality of the ventilation ducts.

              11.8使用.jpg

              3、通風管道加工不能采用S型插條和C型直角插條的連接方式,另外對于一些特殊的通風管道來說,還不能采用按扣式的咬口。

              3. The connection mode of S-shaped and C-shaped right angle inserts cannot be used for the processing of ventilation ducts. In addition, snap joint cannot be used for some special ventilation ducts.

              4、通風管道制作完畢之后,還要用清洗液進行清洗,只有達到清洗標準之后,才可以及時封口。

              4. After the fabrication of the ventilation pipe, it shall be cleaned with cleaning solution. Only when the cleaning standard is met, can it be sealed in time.

              5、玻璃纖維復合板風管端口為切割面時,在裝配法蘭連接件前應將管端切口面用膠帶或膠液進行封堵,才能防止玻璃纖維外露和飛散

              5. When the end of the fiberglass composite board air duct is the cutting surface, the cut surface of the duct end should be sealed with tape or glue before assembling the flange connector to prevent the fiberglass from being exposed and flying

              以上就是為大家介紹的有關濟南風管加工廠的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.globalcarsourcing.com

              The above is a detailed introduction to Jinan Air Duct Processing Factory, and I hope it will be helpful to you. If you have any questions, please contact us. We will provide services for you with our attitude http://www.globalcarsourcing.com


              上一篇:通風管道加工系統布局要減小阻力
              下一篇:最后一頁

              網站首頁 關于我們 產品展示 新聞中心 工程案例 在線留言 聯系我們

              亚洲性视频

                  <pre id="z9x5z"></pre>

                          日本高清视频色视频免费|vvv487 久久久久久久精品免费|1tv610 无毒黄色网站|xt1213 亚洲一区二区三区高清在线观看|xxt168 人人在线视频|v1x197 免费无需播放器看的av|tvx622 日本A级视频在线播放|1vv219 青青青在线网站|tx2284 国产三级片|xx2968 武侠 欧美 另类 人妻|vxx15 奇米影视首页|t2x510 亚洲色网站|xxx175 男人在线视频|0tt846 四虎永久在线精品免费|xx0702 99热最新地址|vvx21 特别黄的视频免费播放|v0t81 国产激情一区二区三区在线|vvv595 大JI巴好好爽好深的视频|1tt872 偷自视频区视频首页|vtx783 国内自拍视频在线|1vx865 日本高清视频色视频免费|tt1368 国产瑜伽白皙一区二区|vx188 超碰最新网站|xxv26 五月天亚洲图片婷婷|x9x122 99久久就热视频精品热线|ttt855 在线观看免费av网站|9xv188 99国产热视频在线观看|xt094 caoprn在线视频免费|xvx237 97在线观看视频|t0v638 国产精品久久精品|ttt368 国自产视频在线观看|0vv164 青青久在线视频免费观看|vx0512